Betriebsstelle Lokwechsel oder Rangierbereich/en: Unterschied zwischen den Versionen
Aus RailRoad&Co.-Wiki
Zur Navigation springenZur Suche springen
Uslex (Diskussion | Beiträge) Die Seite wurde neu angelegt: „:''Fig: Operating points''“ |
Übernehme Bearbeitung einer neuen Version der Quellseite |
||
(14 dazwischenliegende Versionen von 2 Benutzern werden nicht angezeigt) | |||
Zeile 1: | Zeile 1: | ||
<languages/> | <languages/> | ||
__NOTOC__ | __NOTOC__ | ||
{{TC10g}} | {{TC10g}} | ||
Zeile 18: | Zeile 19: | ||
=== locomotive change or shunting area === | === locomotive change or shunting area === | ||
Mr. Freiwald writes about this in [https://www.freiwald.com/forum/viewtopic.php?p=271983#p271983 forum] | |||
At the '''operating station locomotive change''' the locomotive is changed. This means: | |||
* a locomotive is separated from the incoming train, | |||
* | * drives out | ||
* | * and another locomotive drives in | ||
* | * and is added to the train. | ||
* | |||
Therefore, not only an '''entry block''' is always required, but also an '''exit block''' over which the separated locomotive can exit. | |||
If it is only a matter of bringing a locomotive in and adding it to a train, the '''shunting area operating point''' can be used for this purpose. | |||
== Weblinks == | == Weblinks == | ||
* Those: [https://www.freiwald.com/forum/viewtopic.php?p=271983#p271983 forum] | |||
* | *TC-wiki: [[Special:MyLanguage/Schneller Aufrücken|Faster advancement]] | ||
*TC-wiki: [[Special:MyLanguage/Schneller Aufrücken| | |||
:-- [[Special:MyLanguage/Benutzer:Uslex|Uslex]] ([[Benutzer Diskussion:Uslex|Diskussion]]) 18:11, 2. Jan. 2025 (CET) | :-- [[Special:MyLanguage/Benutzer:Uslex|Uslex]] ([[Benutzer Diskussion:Uslex|Diskussion]]) 18:11, 2. Jan. 2025 (CET) | ||
:bearbeitet: DeepPurple 20:13, 8. Jan. 2025 | |||
[[Kategorie:Software]] | [[Kategorie:Software{{#translation:}}]] | ||
[[Kategorie:TrainController]] | [[Kategorie:TrainController{{#translation:}}]] | ||
[[Kategorie:Betriebsstelle{{#translation:}}]] | [[Kategorie:Betriebsstelle{{#translation:}}]] |
Aktuelle Version vom 9. Januar 2025, 17:13 Uhr
locomotive changeover depot
Locomotive change without exit
I want to use the locomotive change operating point to drive a locomotive up to the rear of the train. How do I go about it?
- Fig: Operating points
locomotive change or shunting area
Mr. Freiwald writes about this in forum
At the operating station locomotive change the locomotive is changed. This means:
- a locomotive is separated from the incoming train,
- drives out
- and another locomotive drives in
- and is added to the train.
Therefore, not only an entry block is always required, but also an exit block over which the separated locomotive can exit.
If it is only a matter of bringing a locomotive in and adding it to a train, the shunting area operating point can be used for this purpose.
Weblinks
- Those: forum
- TC-wiki: Faster advancement
- -- Uslex (Diskussion) 18:11, 2. Jan. 2025 (CET)
- bearbeitet: DeepPurple 20:13, 8. Jan. 2025